{"product_id":"light-bracket","title":"Light bracket","description":"\u003cp\u003e Light dome support bracket\u003c\/p\u003e\n\n\u003cp\u003e Suspension bracket for Light Dome, Reptile Dome or Wire Light\u003c\/p\u003e\n\n\u003cp\u003e Easily adjustable\u003c\/p\u003e\n\n\u003cp\u003e Extends the life of light bulbs\u003c\/p\u003e\n\n\u003cp\u003e Suspends lighting fixtures safely\u003c\/p\u003e\n\n\u003cp\u003e Helps prevent accidental re-starting\u003c\/p\u003e\n\n\u003cp\u003e Prevents damage to the terrarium\u003c\/p\u003e\n\n\u003cp\u003e With self-adhesive support base\u003c\/p\u003e\n\n \u003cp\u003eThe Exo Terra Light Bracket is designed to securely suspend a dome or wire fixture above an Exo Terra Natural Terrarium or any other glass terrarium. The Exo Terra Light Bracket easily adjusts in height to accommodate most fixture types or to adjust the heat\/light to suit your terrarium conditions. Once the bracket and fixture are installed, bulbs (such as track lights, Solar Glo, etc.) are no longer subject to movement, resulting in a longer lifespan.\u003c\/p\u003e\n\n\u003cp\u003e Installation and use:\u003c\/p\u003e\n\n \u003cp\u003eGlass Surface Preparation: The surface temperature for application should be no lower than 60°F (16°C) and no higher than 85°F (29°C). If the climate does not permit, move the unit to appropriate conditions. The area to receive the tape should first be thoroughly cleaned with a liquid detergent and warm water solution. Rinse with clean water and dry completely. A final 50\/50 alcohol\/water wipe is highly recommended for best results (use a clean, lint-free cloth). Make sure the surface is dry and free of residue before proceeding. Note: The position of the adhesive backing cannot be changed once it has been affixed.\u003c\/p\u003e\n\n\u003cp\u003e Loosen the screw on the back of the adhesive backing base and remove the light bracket from the adhesive backing base.\u003c\/p\u003e\n\n \u003cp\u003eWith the protective backing still intact, place the adhesive backing base on the back or side of the terrarium to determine its final position and mark the location with a wax crayon or other marker.\u003c\/p\u003e\n\n\u003cp\u003e Remove the protective backing and carefully attach the adhesive backing base inside the marked area.\u003c\/p\u003e\n\n\u003cp\u003e Press the tape firmly and evenly against the glass panel, rotating gently, to ensure proper adhesion. Make sure there are no air bubbles. Let the light bracket rest on the terrarium mesh for 24 hours to allow the tape to cure properly before the dome is suspended and the weight of the dome can apply pressure to the adhesive backing. Once in place, the adhesive backing must not be removed!\u003c\/p\u003e\n\n\u003cp\u003e Allow the tape to cure for 24 hours before inserting the bracket into the adhesive mount base or suspending any device on the bracket.\u003c\/p\u003e\n\n \u003cp\u003eAfter 24 hours, insert the bracket into the adhesive backing base, adjust to the desired height and tighten the screw.\u003c\/p\u003e\n\n\u003cp\u003e Remove the first rubber washer, slide the fixture holder ring onto the light bracket shaft, then replace the first rubber to securely fit the fixture holder between the two rubber stoppers.\u003c\/p\u003e\n\n\u003cp\u003e Adjust the position of the appliance by moving the rubber washers.\u003c\/p\u003e\n\n\u003cp\u003e Adjust the height and tighten the screw of the adhesive support base when the dome frame is suspended above the terrarium at the desired height.\u003c\/p\u003e\n\n\u003cp\u003e Make sure the focal point of the light is not positioned above the plastic parts of the terrarium or screen cover to avoid damage.\u003c\/p\u003e\n\n\u003cp\u003e INSTALL THE LIGHT AFTER 24 HOURS TO ALLOW THE TAPE TO CURE PROPERLY\u003c\/p\u003e\n\n\u003cp\u003e NOTE: FAILURE OF THE TAPE TO ATTACH PROPERLY CAN BE ATTRIBUTED TO ONE OF FOUR PROBLEMS:\u003c\/p\u003e\n\n\u003cp\u003e Poor surface preparation and\/or application.\u003c\/p\u003e\n\n \u003cp\u003ePoor adhesive contact: Exposed adhesive side of the tape that is touched or contaminated.\u003c\/p\u003e\n\n\u003cp\u003e Insufficient pressure is applied.\u003c\/p\u003e\n\n\u003cp\u003e Lamp hung too early, tape not fully hardened.\u003c\/p\u003e","brand":"Exoterra","offers":[{"title":"Default Title","offer_id":50970859143514,"sku":"","price":19.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0555\/6453\/3869\/files\/IMG_0424.jpg?v=1744362341","url":"https:\/\/animal-instinct.it\/en\/products\/light-bracket","provider":"Animal.Instinct","version":"1.0","type":"link"}